Home / Factory

Not a broker.
Our own floor, Dongguan.

When you send Primofort a part, it is printed on machines we own and run ourselves — no outsourcing chain, no middlemen. Every photo on this page tagged as "our floor" was taken inside our own facility.

Get a quote See the floor

30+ industrial printers^CONFIRM Founded 2019 Climate-controlled facility NDA on request

Proof, not promises

Our own production floor.

These photographs were taken on our production floor in Dongguan. No stock photography, no borrowed factory shots — this is where your part actually gets printed.

Formlabs Fuse SLS printer fleet at Primofort

Formlabs Fuse series — our production floor, Dongguan

Farsoon large-format SLS systems at Primofort

Farsoon large-format SLS — our production floor

A row of SLS printers on Primofort's production floor

Production floor, Dongguan

Wide view of Primofort's production floor

Wide view of the floor — our own machines, our own building

Machine count

We currently describe our fleet as 30+ industrial printers^CONFIRM across SLS, MJF and PolyJet. That number is carried over from an earlier version of our own website and has not yet been re-counted machine by machine, so we are treating it as unconfirmed until we do — the honest figure matters more to us than a bigger-sounding one.

Environment

A climate-controlled facility.

Nylon powder and printed parts are sensitive to temperature and humidity swings, so the floor runs in a climate-controlled space rather than an open warehouse.

Environmental monitor on Primofort's production floor reading 28.0 degrees Celsius and 40.2 percent relative humidity

Environmental display, our production floor

One reading, one moment. Our environmental monitor was reading 28.0 °C / 40.2% RH when this photo was taken. We're publishing it as an observed measurement from our own floor, not as a guaranteed constant — conditions are managed, but we are not stating a fixed number as a contractual spec. Ask us for current conditions at quote time.

Quality control

Checked against your drawing, not just "it looks right".

Every part is dimensionally checked against the drawing you supply before it ships — not a visual once-over. If your drawing calls out critical dimensions, tell us and we will measure and report against them specifically.

What we check

Dimensional conformance to your drawing. Critical dimensions are measured and checked against the tolerances you specify, not an assumed default.
Visual and surface inspection. Warping, incomplete fusion, and surface defects are checked before a part is packed.
Material traceability. Each build is tied to the material batch used, so a question about a specific part can be traced back.

What we will tell you honestly

We do not currently publish an accreditation claim. Nothing about formal quality certification appears on this site until Primofort confirms what it actually holds — see pending verification.
Tolerance depends on your geometry. We confirm what is achievable for your specific part at quote, rather than quoting one number for every job.
We are not a broker. Nothing is subcontracted to a third-party shop without telling you — if we ever needed to, we would say so.

The platforms we run

Manufacturer photography, so you know what prints your part.

These two images are the machine manufacturers' own photography of the platforms we run — shown to illustrate the machine, not our premises. Our floor photos above are the only images on this page that show our actual facility.

Formlabs Fuse series

Compact SLS running Nylon 11, Nylon 12 and glass-filled Nylon 12, with a 160 × 160 × 300 mm usable envelope. The workhorse for prototypes and small batches.

Image: Formlabs · formlabs.com — machine photography, not our premises

Farsoon FLIGHT HT1001P large-format SLS system

Farsoon large-format SLS

The large-format side of the floor — where single-piece parts up to 910 × 430 × 400 mm^CONFIRM are printed whole rather than cut and bonded. That envelope is Primofort's own operating limit, not a figure Farsoon publishes.

Image: Farsoon Technologies · farsoon-gl.com — machine photography, not our premises

Machines on our floor

HP Stratasys

HP and Stratasys shown as text — no clean logo mark available for reproduction here.

Primofort · 元城科技 — Room 303, Building 3, Huakecheng, Guanchang Rd, Dongcheng, Dongguan, Guangdong 523128, China

Get a quote

An engineer replies within 24 hours.

Real engineer, real quote. Not an auto-mailer — a person who has read your requirements and looked at your part.
Your IP stays yours. We send a secure link for CAD files; nothing is shared outside the project team. NDA on request.
Not a broker. Your part is printed on the floor shown above — not sent to a third-party shop.

Prefer direct? service@primofort.com · +86 158 9991 6661 (WhatsApp)

Not a broker.Our own floor, Dongguan.